Parts index / 10 results
All products
Compare the mounting, not just the silhouette. USD, applicable tax included.
UPU-T01 / Bucket teethA broad single-point wedge with a horizontal retaining-pin seat. Compare the pocket taper, pin center and adapter nose before selecting; the pin and adapter are not included.
- Construction
- Cast steel; broad tapered wedge; horizontal pin bore
- Dimensions
- Length 230 mm; width 100 mm; height 85 mm; adapter pocket entrance 78 × 60 mm; pin bore 20 mm
UPU-T02 / Bucket teethA long, narrow single-point construction with a transverse retention seat. Select by the measured adapter geometry and pin position, not by the machine name alone.
- Construction
- Cast steel; long narrow point; transverse pin seat
- Dimensions
- Length 285 mm; width 72 mm; height 88 mm; pocket entrance 66 × 58 mm; cross-pin bore 18 mm
UPU-T03 / Bucket teethTwo separated digging tips form a visibly forked nose. Its wider profile is a different selection from a narrow penetration point; confirm the adapter and side-pin geometry.
- Construction
- Cast steel; bifurcated twin tips; lateral pin seat
- Dimensions
- Length 260 mm; overall width 145 mm; height 90 mm; pocket entrance 80 × 62 mm; pin bore 22 mm
UPU-T04 / Bucket teethA broad cupped flared lip and raised two-hole heel distinguish this bolt-on construction from socket teeth. Confirm the mounting face, hole centers and fastener clearance before fulfilment.
- Construction
- Cast steel; broad cupped flared lip; two-hole raised heel
- Dimensions
- Length 215 mm; lip width 165 mm; heel thickness 22 mm; two 18 mm holes at 70 mm centers
UPU-T05 / Bucket teethA thick chisel-shaped nose with a recessed lock seat. The matching lock system and adapter must be checked separately; no lock or adapter is supplied with this single tooth.
- Construction
- Cast steel; reinforced chisel nose; recessed rotary-lock seat
- Dimensions
- Length 275 mm; width 110 mm; height 105 mm; pocket entrance 84 × 70 mm; lock recess 32 mm
UPU-F01 / Hydraulic filtersAn enclosed spin-on element with a threaded base and annular face gasket. Thread and gasket dimensions do not establish circuit suitability; confirm the housing specification before fulfilment.
- Construction
- Steel canister; enclosed pleated media; NBR base gasket
- Dimensions
- Height 145 mm; body diameter 93 mm; mounting thread 1–12 UNF; gasket ID 62 / OD 72 mm
UPU-F02 / Hydraulic filtersA replaceable pleated cartridge with an open central bore at both ends. Check housing length, core diameter, end-seat compression and seal material with the housing specification.
- Construction
- Pleated cellulose composite; steel end caps; NBR end seals
- Dimensions
- Length 200 mm; outside diameter 80 mm; open core 40 mm at both ends
UPU-F03 / Hydraulic filtersA mesh basket strainer with a threaded neck rather than pleated paper media. Check the suction assembly thread, clearance and service requirements; no mesh rating is asserted.
- Construction
- Stainless woven mesh; steel cage; threaded metal neck
- Dimensions
- Basket length 125 mm; diameter 70 mm; male neck thread 3/4 NPT; overall length 155 mm
UPU-F04 / Hydraulic filtersAn exposed pleated cartridge with a partial support sleeve, sealed lower spigot and additional side port. This is an element, not a pressure-rated housing. Confirm both port seats, housing geometry and circuit/media requirements before fulfilment.
- Construction
- Pleated synthetic composite; partial perforated steel support sleeve; NBR lower-spigot O-ring
- Dimensions
- Length 160 mm; outside diameter 60 mm; lower spigot 28 mm; side port outside diameter 18 mm; O-ring section 3 mm
UPU-F05 / Hydraulic filtersA compact vented tank-breather construction with a threaded base. It is not a replacement for a hydraulic flow-line element; confirm tank port, clearance and required breather specification.
- Construction
- Coated steel vent cap; pleated inner element; threaded base
- Dimensions
- Overall height 75 mm; cap diameter 65 mm; male base thread 1/2 NPT